-
Who this checklist is for
-
Step 1: Pick the lamp type before you look at wattage
-
Step 2: Calculate coverage area, not "wattage needed"
-
Step 3: Set hanging height — and stop asking for one number
-
Step 4: Check PPFD distribution before you commit
-
Step 5: Verify controller compatibility before ordering lights
-
Step 6: Calculate electrical load — the step almost everyone skips
-
Step 7: Plan for 20% spare capacity
-
Common mistakes and things to watch
Who this checklist is for
I've been handling grow light installations for B2B clients — greenhouses, commercial indoor grows, controlled environment agriculture — for 7 years. I've personally made (and documented) 11 significant mistakes, totaling roughly $4,200 in wasted budget. Now I keep the checklist to stop other people from repeating them.
This checklist is for anyone setting up or retrofitting a grow space: commercial growers, greenhouse operators, facility managers. It's written for people who need the lights working right the first time, not people experimenting for fun.
Seven steps, in order. Here's what I do.
Step 1: Pick the lamp type before you look at wattage
Most people start with "how much power do I need" and buy from there. That's backwards. Decide the mounting format first, because that determines what you can physically install.
Two categories cover most B2B installs:
Light pendants hang from a fixed ceiling structure. They work well for multi-tier racks, fixed-height benches, and repeated bays where the ceiling geometry is predictable. If your ceiling is inconsistent, pendants get expensive fast.
Standing spotlights (with built-in stands or track systems) work for individual plants, temporary isolation areas, and irregular layouts where you can't drill into the ceiling. Less efficient at scale, but far more flexible.
In 2018, I bought 42 pendants for a 3,000 sq ft greenhouse without checking ceiling height. It peaked at 14 feet in the bays and dropped to 9 feet at the edges. Half the lights were unusable at the edge bays. Cost me $760 in return shipping and a two-week delay.
Checkpoint: Walk the space with a tape measure. Note ceiling height every 10 feet. If it varies more than 3 feet, pendants alone won't work.
Step 2: Calculate coverage area, not "wattage needed"
Wattage is a proxy. What you actually need is a PPFD target across a defined footprint.
Rough PPFD targets at canopy:
- Leafy greens: 200–400 µmol/m²/s
- Herbs and seedlings: 300–500
- Fruiting and flowering crops: 600–900+
A 200W-class fixture — the SF-2000 is a common example — delivers roughly 500–700 PPFD over a 2x4 ft footprint at 18 inches. Double that to a 480W fixture like the SE5000, and you get a 4x4 ft footprint at similar PPFD. Same intensity, bigger area.
So the real question isn't "how many watts," it's "how many square feet at what target." If a listing claims "covers 4x8," find the height and the PPFD. If they won't give both, treat the claim as marketing.
Checkpoint: Write down your footprint (L x W), your target PPFD, and the fixture's PPFD map. If any of the three is missing, don't buy yet.
Step 3: Set hanging height — and stop asking for one number
The question I get asked most: how far does a grow light need to be from plants? People want a number. There isn't one, because the answer depends on two variables — the PPFD you want and the heat the fixture produces.
General starting points for LED fixtures:
- Under 150W: 12–18 inches from canopy
- 200–400W: 18–24 inches in veg, 12–18 inches in flower
- 400W+: 24–36 inches
The mistake almost everyone makes is hanging too close. I've watched growers put a 300W LED 6 inches above the canopy because "closer is brighter." Yes, brighter. Also past the point of photoinhibition for most crops. Leaves bleached, tips burned, three weeks of growth lost.
At 8 inches, a typical 300W LED can push 1,000+ PPFD directly beneath the center. That's fine for a few crops. Not fine for most.
Checkpoint: Hang at the higher end of the range. Measure PPFD at canopy. If it's over 900, raise the light. If it's below your target, lower it slowly — 2 inches at a time.
Step 4: Check PPFD distribution before you commit
Nobody does this. Everyone should.
After hanging, take a PPFD reading at five points: center and four corners of your footprint. Use a PAR meter if you have one. A phone-based PPFD app if you don't — less accurate, still useful for relative comparison.
If the center reads 800 and the corners read 400, you have a non-uniform field. The plants under the corners will grow noticeably slower. Either add fixtures or reduce spacing between them.
Aim for 80% uniformity at minimum — corner reading divided by center reading. Below that, your effective coverage is smaller than your fixture footprint.
Checkpoint: Five readings, one map. If the lowest number is below 75% of the highest, adjust spacing or add a fixture before planting.
Step 5: Verify controller compatibility before ordering lights
This one has burned me and it's the mistake I see most often in B2B installs.
Lights and controllers have to speak the same protocol. Spider Farmer's GGS controller uses specific dimming protocols — Zigbee, 0–10V, or proprietary depending on the model. If you buy a third-party controller without checking, you may end up with fixtures you can't dim.
In 2020, I ordered 60 fixtures for a client and didn't check the dimming protocol against the controller we'd already specified. Non-compatible. We had to swap every fixture for a 0–10V-compatible model. $1,240 down the drain plus a month's delay.
Checkpoint: Confirm the dimming protocol on both the fixture datasheet and the controller datasheet. Match them. Write it down. Do not assume "smart controller" means "works with everything."
Step 6: Calculate electrical load — the step almost everyone skips
Here's the one most people miss. Everyone calculates total wattage. Almost nobody calculates amperage against their existing circuits.
A 480W fixture draws roughly 4A at 120V, or 2A at 240V. Sixty fixtures at 120V is 240A. That doesn't go on a standard 20A circuit. It doesn't go on two of them.
Do this math before you order anything:
- Total wattage of all fixtures
- Divide by your circuit voltage (120V or 240V)
- Add 20% headroom for safety and startup draw
- Compare against your breaker panel capacity
In 2023, I tripped an entire greenhouse circuit because I skipped this. The lights needed a new 60A subpanel that should have been ordered three weeks earlier. Two thousand dollars of crop damage from the outage.
Checkpoint: Total amps calculated. Breaker panel capacity confirmed with an electrician. If you don't have 20% headroom, don't energize.
Step 7: Plan for 20% spare capacity
Don't max out your lighting from day one. If 480W covers your 4x4 at target PPFD, buy the 480W fixture but plan the electrical and mounting layout for 600–800W of capacity.
Growers almost always add density within the first year. Either more plants per square foot, or a second tier. If your layout is already at 100%, that upgrade means a full redesign.
This is where I'd argue quality matters more than price. A fixture with a dimmable driver running at 70% lasts longer and gives you room to scale. The cheapest option at max output has no headroom.
Checkpoint: On your layout drawing, mark the spare capacity percentage. If it's under 15%, revise before installation.
Common mistakes and things to watch
Price-check before every order. Fixture pricing moves. If you're searching for the current spider farmer sf-2000 led grow light price or comparing deals, verify against the manufacturer's site or an authorized dealer on the day you order. Gray-market listings sometimes ship older driver revisions that behave differently.
Read reviews for data, not sentiment. When I look at spider farmer se5000 led grow light reviews, I skip the "great light, plants love it" section. I look for PPFD maps, driver model numbers, and reported failure points at 12–18 months. A review without PAR data doesn't help you predict anything.
Don't trust "covers X square feet" without a height. Any coverage claim without a hanging height and a PPFD value is a marketing number. Ignore it.
Lighting alone doesn't fix a bad grow. Temperature, humidity, and CO2 have to be dialed in alongside PPFD. A premium fixture in a poorly controlled room underperforms a mid-tier fixture in a tightly controlled one. I've watched growers spend $8,000 on lights to "solve" a temperature problem. It made things worse.
Compatibility is a tax you pay upfront or later. Every dollar you save skipping the controller check becomes three dollars fixing it after the install. I know this from the wrong end of the ledger.
Run the seven steps in order. If any checkpoint fails, stop and fix it before moving forward. That's the whole method — nothing clever, just not skipping the parts that hurt later.