-
Where do I even start with office lighting?
-
Are Spider Farmer 100W lights overkill for an office?
-
What about grow light bars like the Spider Farmer Glow30?
-
What should I check before ordering a chandelier stand?
-
Are sensor downlights worth it in hallways and restrooms?
-
Can we change a light switch with the power still on?
-
The vendor says they handle "everything lighting." Should I believe that?
I've handled facilities and office purchasing for a 180-person company since 2021. My annual spend across roughly 20 vendors sits around $340K, and a decent slice of that is lighting — ceiling fixtures, downlights, bulbs, switches, and whatever the break room plant wall needs this quarter.
I am not an electrician. I am not a horticulturist. I'm the person who gets three quotes, verifies the invoice, and explains to finance why the lobby plant lights cost more than the printer lease. So everything below comes from that seat, not from a spec sheet.
These are the questions I actually get — from coworkers, from new hires, and from other admins who message me on LinkedIn:
- Where do I even start with office lighting?
- Are Spider Farmer 100W lights overkill for an office?
- What about grow light bars like the Glow30?
- What should I check before ordering a chandelier stand?
- Are sensor downlights worth it in hallways?
- Can we change a light switch with the power still on?
- The vendor says they handle "everything lighting." Should I believe that?
Where do I even start with office lighting?
Start with the task and the installation, not the product. Ambient, task, or accent — those are three different purchases and they get quoted three different ways. Get the lux numbers first.
ANSI/IES RP-1, the recommended practice for office lighting, puts general ambient lighting in the 300–500 lux range, roughly 30–50 footcandles depending on the task. If a spec sheet doesn't give you lux or footcandles at a stated mounting height, you're buying a vibe, not a light.
Then ask who's installing. In-house facilities, a licensed contractor, or "the guy who does our HVAC"? That answer changes what you can legally buy. Fixtures that need a junction box swap aren't a maintenance-cart job.
After that: voltage, dimming protocol (0–10V vs. phase-cut vs. DALI), and whether the driver is serviceable. A $40 fixture with a sealed driver is a $40 fixture you throw away in three years. I've made that mistake. Twice.
Are Spider Farmer 100W lights overkill for an office?
Depends entirely on the plant, not the room. We bought two of the 100W-class units for the break room plant wall back in 2023, and they've been fine — but I evaluated them as a purchaser, not as a grower.
Three things I check on any grow light listing now:
- Actual wall draw, not "equivalent." Ask the vendor to state watts at the plug. Some listings use "100W" to mean "replaces a 100W bulb," which is a completely different number. Get it in writing.
- Safety listing. UL or ETL, on the unit itself, not just on the power cord. If the listing isn't stated on the product page, assume it isn't there.
- Heat and air. These are not decorative bulbs. They throw real heat and the light is unpleasant at eye level, so ceiling height matters. Ours sit about 9 feet up in a room with airflow from the HVAC return. I would not put one in a closed cabinet or a windowless storage room.
Price-wise, the 100W units I looked at listed somewhere in the $80–$140 band in early 2025 depending on bundle and controller. Verify current pricing — that's a moving target.
Here's my boundary: I can tell you about the invoice, the listing, and the circuit load. I can't tell you whether the spectrum is right for what you're growing. That's a horticulture question and I'd be guessing.
What about grow light bars like the Spider Farmer Glow30?
The bar format is genuinely useful for shelving and rack setups, because the light spreads along a shelf instead of dumping from one point. We added a set to the break room rack and they did what they said on the box.
The friction was mounting, not light quality. I said "standard shelf" on the order and our shelves have a rolled front lip that the included clips didn't grip. They heard "standard shelf" too. We both meant different things. Discovered it when two bars ended up zip-tied to a rack because I didn't want to reorder clips.
So before you buy: measure the shelf thickness and the lip depth, check the daisy-chain limit per circuit, and confirm whether the controller you already have (or the GGS-style controller it ships with) is the same generation. Two bars at roughly 25–35W each won't trip a 15A circuit, but ten of them plus a space heater will.
Also — and this is the part sellers skip — mount them so the driver isn't buried against the shelf. Heat has nowhere to go in a closed rack, and that's where you get early failures.
What should I check before ordering a chandelier stand?
This one surprised me the first time. A chandelier stand isn't decor — it's a load calculation.
Ask three questions before the PO goes out:
- What's above it? Drywall with no blocking, a joist, or a concrete slab. The answer decides whether you need a structural consult or just a proper hanger.
- Is the box rated for the load? NEC Article 314 covers box support requirements, and a box that's fine for a 2 lb. pendant is not fine for a 30 lb. fixture. This is a real failure point, not a hypothetical.
- Who assembles it? Stands ship flat. The assembly hardware is often metric, the instructions are often translated twice, and the person assembling it is often whoever's free on Thursday.
And I'll say the quiet part: I'm not a structural engineer, so I can't tell you whether your ceiling handles a particular load. I can tell you to get that answer in writing from someone who is, before the stand ships. That one email has saved me from a very bad month.
Are sensor downlights worth it in hallways and restrooms?
Usually yes, but the vocabulary will get you. "Occupancy sensor" and "vacancy sensor" are not the same thing, and the difference shows up in a conference room at 2 p.m.
I ordered "motion sensor downlights" for our small conference room. They switched off after 30 seconds of stillness. Turns out they were occupancy sensors with a factory-set hold time, and nobody moves enough during a 45-minute budget review. Nine people, lights out, mid-sentence.
What I ask for now, in writing:
- Sensor type and detection tech — PIR vs. microwave. Microwave passes through glass and thin partitions, which is a red flag next to a corridor window.
- Hold time range and sensitivity adjustment — adjustable, or fixed at the factory?
- Dimming compatibility. If the rest of the floor is 0–10V and your new downlight is phase-cut, you now own two lighting systems.
- Lumen output and CRI. Cheap sensor downlights often land around 80 CRI, which looks gray in a mirror-heavy restroom.
If your building falls under a state energy code like California Title 24, the occupancy/vacancy and control requirements are specified, not optional. Worth a check before you buy 40 of them.
Can we change a light switch with the power still on?
No. Not "probably not." No.
OSHA 29 CFR 1910.333(a)(1) requires live parts to be de-energized before work is performed, with narrow exceptions for cases where de-energizing would introduce a greater hazard. "The breaker panel is in the basement" is not one of those exceptions.
Even when the switch leg is dead, the box can hold another circuit — a traveler from a 3-way, a neutral shared with the room next door, or a hot that the last person left unmarked. Test before you touch, with a non-contact tester and a meter, not one or the other.
And this is where I stop being helpful and start being a liability. Swapping a switch is a $120–$250 electrician service call in most markets. The alternative is a hospital bill and an insurance conversation. For smart switches and 3-ways, the wiring isn't intuitive and the instructions assume you already know what a traveler is.
If your question is literally "how do I change a switch with the power on," the answer is: you hire someone. That's the whole answer.
The vendor says they handle "everything lighting." Should I believe that?
Be careful. We had a full-service lighting vendor who quoted fixtures, installation, and disposal as one package. Two fixtures arrived damaged, and the install was subbed to a contractor nobody had vetted. When the damage claim came up, the vendor pointed at the installer and the installer pointed at the shipper. Three weeks, four emails, one very patient VP.
The vendor I still use today does one thing — they spec and sell commercial fixtures. They told me upfront they don't install and handed me the name of a licensed contractor they've worked with for years. That "we don't do that" earned them the rest of my business.
Bottom line: a specialist who knows their limit is easier to manage than a generalist who says yes to everything. When someone claims to cover design, supply, install, and service, ask which parts are in-house and which are subcontracted. If they can't answer cleanly, that's a deal-breaker for me — not because subcontracting is bad, but because I need to know who's actually on the hook when something breaks.
Ask the question. The good ones answer it in one sentence.