Houston · New York · London · Singapore Request a Specification Review

We Buy Spider Farmer Grow Lights—Why the Spec Sheet Is the Last Thing I Check

The number on the box is not the number in the room.

I handle procurement for a horticulture company—roughly 180 people, about $400,000 a year across maybe a dozen vendors, including everything that goes into our small indoor grow room. My job is not to pick spectra. My job is to make sure whatever the grow team asks for actually shows up, gets installed, and runs through a full season without turning into my problem or theirs.

And here's what I've learned the hard way over the past few years: the PPFD number on the spec sheet is the easiest thing to compare and the least useful thing when it comes to what actually happens in your room.

That's not an anti-science take. That's just separating the light itself from the light as installed, wired, and living in your building. Let me get into what we ran into.

“How to hang a light from the ceiling” is not an FAQ. It's the bottleneck.

The first thing that actually slowed our project down had nothing to do with light. It was the ceiling.

We were looking at spider-farmer grow lights—the team had compared the SF and G series and settled on full-spectrum LEDs, with a batch of spider farmer glow30 led grow light bars for strip supplemental lighting over the transplant area. The specs were fine. The PPFD distribution chart looked clean. But nobody had asked a basic question: can we hang these things?

Old building. Steel beams. Uneven ceiling height. We weren't just asking “how to hang a light from the ceiling”—we were asking how to hang a row of them, evenly spaced, with adjustable height, and in a way that we could move later. That sounds like the installer's problem. It's yours, because different hangers, different cable kits, and different hook styles mean different delivery lists, different install times, and a totally different “wait, that's not enough” moment when the boxes show up.

I remember the first delivery. The hanging cables that came with the order covered maybe half the positions we had planned. Not the supplier's fault—we hadn't written the install plan into the purchase order. The replacement cables cost under $60. The install crew waited almost a week. And during that week, the grow team spread a set of temporary lights across the floor “roughly where the real ones would go,” which meant we ended up re-positioning everything twice.

That taught me something simple: a light's mounting method limits what it can actually do, and the mounting plan belongs on the purchase order, not in someone's head. Height, spacing, adjustment range—putting those in writing was worth more than squeezing twenty bucks off the unit price.

“Zigbee temperature” is a phrase I wish I'd understood earlier

Second batch, we moved to smart controls. The grow team wanted automated dimming, timed on/off, and temperature linkage. Short version: they didn't want to walk over and flip a switch every morning.

My understanding of zigbee temperature automation at that point was roughly “oh, it connects to a smart controller.” It wasn't until we had the GGS controller running that I got what the value actually was: not “you can turn lights on from your phone,” but when the light turns on, how long it stays on, and how hot the room is finally get managed as one thing instead of three.

The old way: lights on a timer, fan controlled by a person, temperature measured by hand. The result was lights and room fighting each other all day. Midday in summer, everything on, the room hot to the touch, the grow team walking in and saying “let's not run all the lights,” then around four o'clock realizing the light wasn't enough, and turning half of it back on. Nobody won that day.

Once the controller was in, “light on” got broken into conditions: above a certain temperature, the lights dim themselves; the photoperiod arrives, the lights follow the schedule. Sounds basic. For a room where the lights are not the only heat source, that's the difference between gut feel and an actual rule.

And I'll be honest about the limit of what I understand here: I still don't fully get how the dimming curve maps to actual output. I want to say it was either a 0–10V interface or straight Zigbee dimming—I'd have to check the paperwork. The grow team says “it dims.” I make sure that when they say it dims, it actually dims on time, every time.

Behind the light switch, temperature is running the show

This is the most counterintuitive piece, and it deserves its own section.

Everyone looks at how bright the light is. But in our room, how hot the lights get, how warm the room gets, and when the temperature peaks probably matter as much as the lamp itself. On a summer afternoon, full power on every fixture and the fan running wide open, the room still climbs into a range the plants don't love. If the lights are dynamic—if they can respond to temperature—then the same fixture “holding back” at noon and “making up for it” in the evening does more good than running flat out all day.

Plainly: the light switch is not binary. We used to treat it as on/off. Now we treat it as when, how much, and under what temperature.

If your room is temperature-controlled to begin with, this may matter less to you. The insulation in ours is, politely, not great. So temperature linkage is not a bonus feature. It's a floor. In the first full quarter after switching to LED, lighting accounted for roughly 40% of the grow room's electricity use according to our own utility dashboard—I want to say 38%, but don't quote me on that.

“But isn't PPFD the thing that matters?”

I get this question every time. The other side of the aisle says the only thing worth comparing is PPFD, or lumens, or spectrum.

I agree—PPFD is the light's baseline. But baseline is baseline. Factory numbers are measured under controlled conditions. Your room isn't controlled.

Same light, hung ten centimeters too high, delivers less to the canopy. Hung too low, the edge of the footprint runs hot. A steel beam in the middle of the room means the neat curve on the PPFD chart has to be redrawn. Add control on top: if turning the light on depends on someone remembering, your promised “fourteen hours of light a day” becomes twelve on a good day.

So my order of operations is backwards on purpose:

  1. Lock the install plan first—where it hangs, how it hangs, can the height change, and how annoying is it to move.
  2. Lock the control plan second—timing, dimming, temperature linkage, and whether it actually runs the way you need it to.
  3. Compare specs last—at this point, the small differences between the remaining options mostly disappear in your actual room.

One useful cross-check: the DesignLights Consortium (DLC) publishes Horticultural Lighting Technical Requirements and a qualified products list, which many utility rebate programs reference. It's not a substitute for your own install plan, but it's a sane filter before you start memorizing PPFD charts.

So what would I actually recommend?

I'm not against spec sheets, and I'm not against comparing PPFD. I just think the light has to be hangable, controllable, and able to live next to temperature before the spec sheet means anything.

For a room like ours—not a commercial grow, but serious about indoor cultivation—Spider Farmer has been useful precisely on the control side. The smart controller, the Zigbee temperature linkage, the hanging options that let us adjust height—those pieces fit together into something you can actually run.

That's not a claim that nobody else can do it. It's a claim about what procurement actually is: can it be installed, can it be controlled, can it be accounted for—not how big the number on the box is.

If I could give one piece of advice to anyone buying grow lights: ask how to hang it first, ask how to turn it off second, and ask how bright it is last.

Get the order wrong, and you're buying a spec sheet. Get it right, and you're buying a light that works.